Wire + Metal: 30 Easy Metalsmithing Designs

By Denise Peck, Jane Dickerson

Easy-to-do strategies on the convenience of your kitchen table!

Authors Denise Peck and Jane Dickerson introduce uncomplicated twine- and metalworking concepts that experience vast effect. operating with precut steel blanks and skinny gauge sheet, in addition to with low-cost and available instruments, you could produce effects just like even more complicated metalsmithing techniques.

Explore lashing, sewing, basic weaving, coils, spirals, twisted twine, and incorporating beads with cord. you may be uncovered to steel items being hole-punched, dapped, hammered, textured, colorized, and patinated. This e-book beneficial properties thirty step by step tasks that require purely uncomplicated jewelry-making talents, yet will lead to beautiful modern jewellery. Wire + Metal covers a variety of kinds that may entice newbie to complex jewellery makers.

Show description

Quick preview of Wire + Metal: 30 Easy Metalsmithing Designs PDF

Show sample text content

As soon as this disc is stamped, flip it over and frivolously hammer the again with the chasing hammer so it lies flat. three. Mark the heart of the 1⁄4" (6 mm) copper disc with the Sharpie and make a gap on the mark with the hole-punch pliers. four. middle the 1⁄4" (6 mm) copper disc on most sensible of the sterling disc and make a mark during the gap with the Sharpie onto the sterling disc. Make a gap on the mark utilizing the hole-punch pliers. Repeat for the massive copper disc and brass disc. flip all of the discs over one after the other and lightly strike the punched gap to flatten the items back.

Connect an ear twine to the pinnacle gap of every disc. assets Sterling silver discs: metalliferous. com. Bead caps: bsueboutiques. com. Texture hammer (inter­changeable nine-face hammer): beaducation. com. Micro screws and nuts: objectsandelements. com. Eyeglass mini screw­driver: drugstore. Ear cord, spray matte end: michaels. com. Renaissance Wax: objectsandelements. com. red Petals Denise Peck fabrics 24-gauge red aluminum sheet 36-gauge textured copper sheet five" (12. five cm) of 20-gauge sterling twine instruments Disc cutter 1.

Concentration the moves at the again region of the band. three. take hold of one finish of the flat twine within the jaws of the bail-forming pliers. begin to roll the cord round the pliers (Figure 1). Roll approximately midway after which turn the twine round and roll back. Repeat at the different finish. it's completely own choice no matter if your loop rolls towards the interior of the band or towards the skin. I happen to love the shadow line that rolling towards the surface makes. determine 1 four. For an etched glance, use 3 coarse grades of sanding pads and randomly rub in several instructions all around the floor.

Four cm) of two mm cording One 1⁄16" (2 mm) shank diameter × 9⁄32" (7. 1 mm) lengthy brass micro screw One 4mm brass micro nut instruments 1. eight mm steel hole-punch pliers Fine-point Sharpie marker 100/180 coarse-grit salon board Spiral steel stamp Brass mallet or ball-peen hammer metal bench block African Bronze Gilders Paste smooth textile Disc cutter steel shears Dapping block Eyeglass mini screwdriver Flat- or chain-nose pliers Heavy-duty flush cutters Scissors Superglue accomplished size Varies 1.

Determine 1 determine 2 three. observe a protecting end (see completing) to maintain the patina. Oven patina 1. Preheat the oven to 300°F (149°C). 2. position your fresh copper parts on a cookie sheet. Bake for roughly 17 mins, checking often after 10 mins, till you succeed in the specified patina (Figure 1. “Before” disc at the left and “After” disc at the right). Quench or air cool. determine 1 three. follow a protecting end to maintain the patina. Nail polish + spray paint Nail polish is a simple and reasonably-priced technique to supply an enamel-like coating to steel.

Download PDF sample

Rated 4.21 of 5 – based on 13 votes